1262
Left Rear Motor Mount Bolt
Wrench
allows removal and
installation of left rear motor
mount bolt on Big Twins without
removing the inner primary
cover.
VT No. 16-0518
5 Piece "S" Box Wrench Set
includes 3/8 x 13/32, 7/16 x 1/2, 9/16 x 19/32, 5/8 x
11/16 x 3/4
VT No.
Item
16-0013
Set
16-1617
Curve
Flat Axle Nut Wrenches.
VT No.
Size
Fits
16-1380
15/16 x 3/4
1999-01 2000-07 ST
16-1381
36 mm x 3/4
2002-07 Touring
16-1382
36 mm x 15/16 2008-up FXD, ST, Touring
16-1381
16-1380
Twin Cam 24 Tooth Crankshaft Rotating Wrench
for use on
all 2006-up Big Twins with 24T spline sprocket shaft to check
engine timing and parts clearance.
VT No. 16-9280
16-1382
Oxygen Sensor Tool
will remove and install oxygen sensors on fuel
injected models. Can be used with 7/8" wrench or 3/8" drive.
VT No.
Fits
16-1131
18mm
16-1132
12mm
Intake Manifold Allen Wrench
cuts work in
half, no need to remove gas tanks, on all
Evo BT & Sportsters.
VT No. 16-1806
Wrench
Evo Rocker Box Cover
Wrench
is designed to reach
3/16" allens on Evo Big Twins
and Sportster models. Features a 3/8" drive for use with torque wrench and a
vinyl covered handle.
VT No. 16-0220
Evolution Ratcheting Intake Manifold Wrench
features ball end allen bit end f or
flexibility in tight areas.
VT No. 16-5530
Evolution Rocker Box Cover Ratcheting Wrench
features low profile to allow
clearance between frame & engine, long handle for increases reach and replace-
able bit.
VT No.
Item
16-6529
Wrench
16-6530
Replacement Bits
16-5530
16-6529
Lower Rocker Box
Wrench for Evo &
Twin Cam Models
is
used to install and
remove lower rocker
7/16" mounting bolts.
VT No.
Fits
16-6531
Evo
16-6532
TC-88
FLT Rear Axle Nut Ratchet Wrench
for 36mm axle nut. Low profile design
allows access to rear axle n ut without
removal of exhaust system.
VT No. 16-9636
Oil Pressure Gauge and Indicator Lamp Sending Unit Wrenches. These
reversible ratcheting wrenches are
used to install and remove oil pressure indi-
cator lamp or gauge sending unit on all FL Touring models 1999-up.
VT No.
Item
16-9723
Indicator Lamp
16-9724
Sending Unit
Speedometer Sending Unit Wrench
features a shortened 3/16" ball end hex bit
for removal or installation of hex screw used on all Big Twin models. Equipped
with electronic sending units.
VT No. 16-6738
Exhaust Bracket Wrench
used to remove and install front exhaust bracket bolts
on all 1999-up TC-88 Dyna models.
VT No. 16-6538
Manifold-Side Car Wrenches
large type, heavy
duty for shop use.
VT No.
OEM
Size
Use
16-0111
94536-18
1 3/4"
Side Car
16-0110
94537-26
1 7/8"
45 Manifold
16-0112
94538-30
2"
SV Manifold
16-0109
94538-48
2 1/8"
BT Manifold
16-6532
16-9723
16-9724
16-6531
Standard Spark
Plug Wrench
14mm
type with bar handle
fits under FL tanks.
VT No. 16-0825
Swivel Spark
Plug Wrench
for
all 12 & 14mm
plugs. 180° rota-
tion.
VT No.
16-0824
Spark Plug Socket Set
features 3/8" drive to fit 12 and
14mm plugs.
VT No. 16-0202
Spotlamp Holder
assists in assembly procedure in
conjunction with signal lamp.
VT No. 16-0515
Hand Held Impact Driver
is a
very efficient tool for those hard to
loosen screws. Complete set
includes main body, adapter, 2
screw bits and 2 phillips bits.
VT No. 16-0151
16-0013
Previous Page
