3rd Hand Axle Locker
If you have noticed, as
you are torquing down the
axle nut after you set the
proper belt tension,
(Deflection) the welded axle nut will move to the low
side of adjuster cam. This movement will allow the belt
to lose adjustment. Now with
Jims 3rd Hand Axle
you will not need to find a helper to hold the n ut
or yourself having to reach around the tire and hold
the nut from moving. Just place this tool over the weld-
ed nut on left side with the nec k portion of tool resting
over the swing arm. Hand screw the adjusting screw to
take up any slack in tool. Torque the axle nut from right
side knowing that the welded nut will not turn allowing
the belt to lose it's adjustment.
Axle lock tool. This tool holds the axle in place and
prevents movement of adjustment while you torque the
rear axle on 2002 and up FLT
Rear Swing Arm Section
for use on 1986-99 FXST-
VT No. 16-0688
Shock Change Tool
holds swing arm in position dur-
ing shock change.
VT No. 16-0076
Swing Arm Bearing Installer
will install both right and
left swing arm bearings
squarely on their bores to the
installed depth on 2002-up
FLT models. Replaces 45327.
VT No. 16-1058
Jims Powertrain Alignment Tool
aligns powertrain to proper position
safely and easily on most tour ing
models. Performing alignment ser-
vice must be done when engine,
transmission or swingarm has been repaired or
removed. This tool helps to provide the accurate align-
ment necessary for handling safety and performance.
For 1993-97 FLHT; FLHR; FLHX & FLTR.
VT No. 16-1365
16-0329 in use
5-Speed Swing Arm Tools
cleve block spreading tool
facilitates installation of swing arms on rubber mount
models. Swing arm assembly tool removes and installs
swing arm pivot components.
Hollow Axle Plug Tool
will give the
correct center point required for
safe vehicle alignment. Lube the o-
ring ends of these tools and inser t
in left and right ends of axle on
Dyna and XL models. Use on all
2008-up Dyna and XL models.
Jims Rear Axle Not Torque
for 2006-up FL Touring
models. This tool is designed with a
1/2" drive receiver hole for inserting
your torque wrench thus letting you
torque the axle nut from an offset
position. Removal of muffler is not
required for use of this tool.
VT No 16-1906
E-Z Squeeze Bearing Packer.
greases all tapered bearings with a 5/8" or larger I.D.
Canister holds grease for clean operation.
VT No. 16-0755
Lincoln Grease Gun.
Small type as early
VT No. 16-0548
Oil Drain Reservoir.
Low profile fits under frames on
ST and FLT models.
VT No. 16-0585
includes drain plug
hex at opposite end.
Seal Puller Tool.
Simply insert the tip of the tool
behind the oil or grease seal, press and pull leverage
works for you. No more pounding, hammering and dig-
ging that might damage bearings. Two size tips reach
in and fit nearly all seal applications.
VT No. 16-0838
Wheel Bearing Greaser.
Fitting & spigot greases
1973-99 tapered bearings
without removing seals, use
existing seal spacer or pur-
into the cable core.
VT No. 16-0686
all spin on fil-
drive. Fits all
Swivel-Flex Oil Filter Wrenches
feature gripper teeth
and a durable treated band with a vinyl covered flex
handle which swivels to clear frame and exhaust
obstructions. Replaces 96221-80.
VT No. 16-0903
. Special thread.
Flat Top Alemite
Grease Fitting Adapter
is designed to be used
on alemite grease fitting,
0340. Tapped 1/8" NPT
to use with standard
VT No. 9929-1