Retrocycle Harley Motorcycle Parts


1 Mars Ct. Unit 3
Boonton, NJ 07005
973-291-8588
 

0 Items in cart
Featured Bike:
1948 FL 74 Cubic Inch

Catalog page 1240

  Previous PageSee PDF versionNext Page  
Page 1
background image
1240
1955-up Sprocket Shaft Hard
Cap
protects shaft when using
press. By Jims.
VT No. 16-0666
Crankshaft Stabilizer
Bracket
acts as third hand.
Sliding over crank splines,
and bolting to a primary
mount hole prevents crank
from turning while installing
pistons, cylinders or rings.
VT No 16-5051
Shaft Turning Tool
fits spline or taper on assembled
motor and allows engine to be tur ned over by "
ratchet or impact driver. Sifton unless noted.
VT No.
Years
Type
16-0150
1930-54
Big Twin, Taper
16-1850*
1955-06
Big Twin, Spline
16-1378*
2006-up
FXD, 07-up FL, FXST
16-1852
1957-up
XL, Spline
*Note:
Jims
16-1850
16-0150
16-1378
16-1852
Sprocket Shaft Seal & Lock Installers
for Big Twins.
VT No.
OEM
Years
Application
16-0153
97235-55B
1955-69
Installs Nut & Seal
16-0888
97235-55B
1955-69
As Above, Jims
16-1754*
39361-69
1970-up
Installs seal only, Jims
*Note:
Use with 16-0140 or 16-1836 to install seal.
16-0153
16-0888
16-1754
Twin Cam 24
Tooth
Crankshaft
Rotating
Wrench
for use
on all 2006-up
Big Twins with 24T spline sprocket shaft to check
engine timing and parts clearance.
VT No. 16-9280
Compensating Sprocket Wrench
to install or remove
compensating sprockets. Replaces 94557-55 for 1955-
69.
VT No.
Item
16-0130
Flat Type
16-0883
1
/
2
" Drive Type, Jims
16-0130
16-0883
Sprocket Shaft Tool
Outer Balancer Bearing Installer &
Remover Tool
removes and installs the
outboard balancer bearing on the new
96" & 110" "B" Softail engines chain
guide support plate.
VT No. 16-1376
Balancer Shaft Removal Tool
designed
to remove both front and rear counter-bal-
ancer shaft bearing assembly, from the
left engine case on the new 96" and 110"
Beta engines.
VT No. 16-1374
Balancing Shaft and Bearing
Installer Tool
designed to align
and safely install a new balancer
bearing and counter balancer
shaft into the new Twin Cam 96"
or 110" "B" Softail engine case.
For removal of balancer shaft
from the engine case use Jims
tool No. 960.
VT No. 16-1377
Jims TC-88 Balancer Shaft Alignment Tool
use for
correct balancer drive assembly. Use on all 2000-up
TC-88B models.
VT No. 16-1166
Balancer Shaft Retention Pin
use this tool to secure
the engine balancers on TC-88B engines when ser-
vicing flywheel assembly. This tool locks into the bal-
ancers sprocket pin holes to prevent the balancer
from turning out of sync with flywheel.
VT No. 16-1163
Balancer Shaft Inner and Outer Bearing
Remover and Installer
for TC-88B models
2000-up includes thrust bearing. Replaces
44066.
VT No. 16-0540
Balance Tool
Jims Twin Cam Case Support Block for Balancer.
Engine 2000-up. These blocks properly support the
case on a level plane when using a press f or work.
VT No. 16-1916
Jims Balancer Shaft Inner Bearing Remover and
Installer Tool
for all 2000-up Twin Cams. This tool will
accurately remove and install the inner balancer bear-
ing mounted in the left case.
VT No. 16-1915
    
V-Twin or
(Harley #)
DescriptionPrice
16-9280Crankshaft Rotating Wrench
Crankshaft rotating wrench
$53.56 EA

16-0666Jims Hard Cap
Jims hard cap tool
$51.33 EA

16-5051Anti-rotation Bracket
Crankshaft stabilizer bracket
$31.23 EA

16-0150Sprocket Shaft Truing Tool
Sprocket shaft truing tool
$39.82 EA

16-1850Sprocket Shaft Turning Tool
Shaft turning tool
$39.95 EA

16-1378Jims Sprocket Shaft Turning Tool
Shaft turning tool
$123.82 EA

16-1852Sprocket Shaft Turning Tool
Shaft turning tool
$36.31 EA

16-0153
(OEM: 97235-55B)
Sprocket Shaft Bearing Nut Wrench
Sprocket shaft bearing nut wrench tool
$45.27 EA

16-0888
(OEM: 97235-55B)
Sprocket Shaft Jim Seal Wrench
Sprocket shaft seal and lock installer
$133.16 EA

16-1754Sprocket Shaft Seal Install Tool
Sprocket shaft seal install tool
$108.69 EA

16-0140
(OEM: 97225-55)
Bearing Tool
Bearing tool
$74.83 EA

16-1836
(OEM: 97225-55)
Jims Sprocket Shaft Bearing Tool
Sprocket shaft bearing tool
$192.29 EA

16-0130
(OEM: 94557-55)
Compensating Sprocket Wrench Flat Type
Flat type compensating sprocket wrench
$39.82 EA

16-0883
(OEM: 94557-55A)
Jims Compensator Sprocket Socket Wrench
Compensating sprocket wrench
$85.77 EA

16-1376Jims Outer Balancer Bearing Installer &
Outer balancer bearing installer and removal tool
$162.79 EA

16-1374Jims Balancer Shaft Removal Tool
Balancer shaft removal tool
$206.50 EA

16-1377Jims Balancer Shaft & Bearing Installer
Balancing shaft and bearing installer tool
$113.46 EA

16-1166Jims Tc88 Balancer Shaft Alignment Tool
Balancer shaft alignment tool
$246.50
$234.18 EA

16-1163Jims Tc88 Balancer Shaft Retention Pin
Balancer shaft retention pin for TC-88
$28.73 EA

16-0540
(OEM: 44066)
Jims Balancer Bearing Remover/installer
Balancer bearing remover and installer tool
$134.41 EA

16-1916Jims Case Support Blocks$85.38 EA

16-1915Balancer Shaft Inner Bearing Service$200.00 EA

Facebook
Vintage Harley Parts    |    Blog    |    Motorcycle Repair    |    Hours and Location    |    Links    |    Parts and Accessories    |    Restoration    |    Powder Coating    |    CAD Plating Parkerizing
Policies    |    Bike Storage    |    Advertising    |    Sell Your Bike    |    Current Auctions    |    Sitemap    |    Bike Gallery    |    Les Dunham    |    Metal Polishing